Analisa Pengaruh Jarak Sudu Terhadap Putaran Turbin Ulir Pada Pembangkit Listrik Tenaga Mikro Hidro

  • I Kadek Ardika
  • Antonius Ibi Weking
  • Lie Jasa

Abstract

Screw Turbine is a turbine that has just been studied. The working principle of this turbine screw is based on a screw pump system which functions to lift water from the river to the surface. The turbine screw is basically the return of the screw pump. To obtain an experimental study of the maximum output produced by a PLTMH using a turbine screw, the research is very difficult to apply in real conditions, and problems with screw turbines are made about the effect of blade distance (10 cm, 12 cm and 15 cm) on efficiency, voltage, current and power on the MHP using a screw turbine. Therefore the research will use a screw turbine prototype on a laboratory with micro power plants. In this study the best measurement at a distance of 21 cm blade with an angle of 280, where the voltage, current, and output power generated by the generator is 129.4 Volts loaded with 60 Watt, No load 162.7 Volts, the current generated is 0.1774 Ampere and the power produced is 22.9 Watts. For generator rotation speed that is equal to 7054 rpm, while turbine rotation speed generated at pressure is equal to 589 rpm before coupling with generator and 318 rpm after coupling with generator, the efficiency obtained in this PLTMH modeling test is at a distance of 22 cm blade with angle slope 280 that is equal to 24.5%.

Downloads

Download data is not yet available.

References

[1] Bahri, A,. 2017. Merancang dan Mengimplementasikan Modul Praktikum Pembangkit Listrik Tenaga Mikro Hidro di Jurusan Teknik Elektro dan Komputer Universitas Udayana Majalah Ilmiah Teknologi Elektro, Vol. 16, (Mei – Agustus ) : 43- 47
[2] Saroinsing, T., Thomas, A.Mekel, A.,N. 2017. Desain dan Pembuatan Trubin Ulir Archimedes Untuk Pembangkit Listrik Tenaga Mikro.ISSN 2447-2097. Vol. 3 2017 : 159-169.
[3] Saefudin, E., Kristyadi, T., Rifki,M., Arifin,S. 2017 Turbin Screw untuk Pembangkit Listrik Skala Mikrohidro Ramah Lingkungan. Jurnal Rekayasa Hijau, Vol. 1 (Oktober) 2017 : 223-244.
[4] Rorres,C. 2000. The Trun Of The Screw : Optimal Design Of AN Archimedes Screw. Journal of Hydraulic Engineering,Vol. 126 (Januari) : 72-80.
[5] Juliana, I., P., Weking, A., I., Jasa, L. 2018 Pengaruh Sudut Kemiringan Head Turbin Ulir dan Daya Putar Turbin Ulir dan Daya Output Pada Pembangkit Listrik Tenaga Mikro Hidro. Majalah Ilmiah Teknologi Elektro, Vol. 17, No. 3, (September – Desember) 2018 : 393- 400
[6] Syahputra, M.T. 2017. Rancang Bangun Prototipe Pembangkit Listrik Tenaga Piko Hidro Dengan Menggunakan Turbin Ulir. e-ISSN 2252-7036, Vol. 2 (Juni) : 16 – 22.
[7] Havendri, A., Arnif,I. 2010. Kaji Eksperimental Penentuan Sudut Ulir Optimum Pada Turbin Ulir Untuk Data PerencanaanTurbin Ulir Pada Pusat Listrik Tenaga MikroHidro (PLTMH) Dengan Head Rendah. Seminar Tahunan Tekni kMesin (SNTTM), Vol. 9 (Oktober) : 273-277.
[8] Setiarso, M., A., Widiyanto, W., Purnomo, S., N. 2017. Potensi Tenaga Listrik dan Penggunaan Turbin Ulir Untuk Pembangkit Skla Kecil di Saluran Irigasi Banjar cahyana.p-ISSN1858-3075, Vol. 1 : 19-27.
[9] Widnyana, I., G., Weking, A., I., Jasa, L. Analisa Pengaruh Tekanan Air Terhadap Kinerja PLTMH dengan Menggunakan Turbin Archimedes Screw. Majalah Ilmiah Teknologi Elektro, Vol. 17, No. 3, (September – Desember) 2018 : 1- 10
[10] Wie,S.D.,AgungA.I. 2018. Perencanaan Dan Implementasi Prototipe Pembangkit Listrik Tenaga Mikro Hidro (PLTMH). JurnalTeknik
Published
2019-06-30
How to Cite
ARDIKA, I Kadek; WEKING, Antonius Ibi; JASA, Lie. Analisa Pengaruh Jarak Sudu Terhadap Putaran Turbin Ulir Pada Pembangkit Listrik Tenaga Mikro Hidro. Majalah Ilmiah Teknologi Elektro, [S.l.], v. 18, n. 2, p. xxxxx, june 2019. ISSN 2503-2372. Available at: <https://ojs.unud.ac.id/index.php/JTE/article/view/49109>. Date accessed: 06 june 2020. doi: https://doi.org/10.24843/MITE.2019.v18i02.P10.